Your vehicle in your hands. All about auto repair.

Replacing CV boot on Gonow Aoosed G5

Steering Professional
Anthony Hernandez
If you want to know how to remove CV boot in your auto, you can see the quick review how to replacing CV boot easy and efficient way!
If you feel that something wrong with information above, so inform us about that!

Are CV boots universal on a Gonow Aoosed G5?

Description. CV Boot - Cut to size Universal boot, will fit 98% of cars. Please note this is not suitable for 'Tri-Lobal' or 'Metal Bonded' Boots.

How does a Gonow Aoosed G5 CV boot work?

The part that simultaneously enables the axle to flex while transmitting the driving force is called a drive axle joint, and is also known as a constant velocity (or CV) joint. The CV Boot is a ribbed, rubber flexible boot that keeps water and dirt out of the joint and the special grease inside the joint.

What happens when the CV axle on a Gonow Aoosed G5 boot rips?

Grease leak: When a CV boot cracks or tears it will usually leak grease onto the inside of the wheel. This leak can eventually be sent into other parts of the chassis or even the underside of the vehicle as the CV axle turns.

How serious is a leaking CV boot?

But CV boots serve a simple but important purpose and allow the CV axles and joints to stay clean and enjoy a long service life. When a CV boot leaks, it can cause the attached joint to become damaged posing a serious safety hazard.

How do you change a CV axle on a Gonow Aoosed G5?

How to replace CV axle on Gonow Aoosed G5 - And the tools we're gonna need is this thirty two millimeter socket right here it's a 12 point socket for this axle bolt. And then usually you need a cutter for a cotter pin that goes here.

How long will a Gonow Aoosed G5 CV joint last with a torn boot?

To keep that all-important grease contained where it should be, each joint is enshrouded by a protective rubber boot, or "CV boot." As long as that boot remains intact, it is not uncommon for CV joints to last well over 100,000 miles or more.

Can a bad CV joint cause knocking?

A CV joint that has become worn out from being used too much will cause a knocking sound. This noise can come from the inner joint on a front-wheel drive car.

How much does it cost to replace a CV boot on a Gonow Aoosed G5?

Car Gonow Aoosed G5 CorollaL4-1.8L
Service Service typeAxle / CV Shaft Assembly - Driver Side Rear Replacement
Estimate Estimate$639.94
Shop/Dealer Price Shop/Dealer Price$771.09 - $1117.21

Are CV boots covered under warranty on a Gonow Aoosed G5?

Yes, they should be. good luck. dealer will not cover if found to have road damage or tear/split caused by outside forces. Some consider CV boots a wear item.

Can a torn Gonow Aoosed G5 CV boot be repaired?

By replacing a torn CV Boot, the joint can be saved keeping the grease in the joint and protecting it from wear. CV Boots should be inspected regularly and replaced immediately if torn. This type of preventative repair can save a lot of money and frustration down the road.
Add comment


Comments on how to fix CV boot on a Gonow Aoosed G5:
Tomas
Just did the flange seal on that side, had to battle the pinch bolt to get the control arms out, couldnt get enough room. No idea how you managed to get the axle out without doing that, your wizard skills are showing once again. Wanted to do the dust boot aswell since its cracked but i cant get that 17mm allen bolt to budge, not even with my 1,5m long cheater bar. And nice job following that torque spec lol. You have to get them tight though, if you go by factory torque spec theres a good chance they will come loose. Ask C5 group members how they know that...
Jiao
bahi sethic greas use keyakaroo
Hondo
Any tips on putting the lower ball joint bolts back on?... I tried one time when I installed a spacer lift and no matter how much I jack up the lower ball joint it was hard to get it close for the bolt to reach the spindle all it was doing was tilting the truck more to the side.
Dallas
Nice work!
Emrys
Super Video... Allerdings eine Frage: Wenn die Achsschenkel demontiert werden, so müsste nicht die Spur neu eingestellt werden?
Artus
Those camera angles are great, well done
Lucas
good shit
Jimmie
Fab stuff, we were at a wedding party in the local hotel, Nippa pulled up at the lights, drew some attention, people asking what it was, I explained!
Kort
Is this the same procedure with a mk5 Golf 2004 1.6L?
Frederico
Hey guys, random question - I have a 2018 GTI in the base (S) trim, and it came with halogen headlights. I bought an LED bulb kit from LASFIT ( I tried to open the hood and switch the bulb, but I am a noob and don't know exactly what I'm doing. Would the LASFIT bulbs work? Thanks
Lay
I enjoy watching your videos MM but I never see you use a torque wrench.
Burne
myturbodieselgotc om, if I want to put a cold air intake on my 03 passat which model would you recommend?
Fateh
Excelente vídeo e información muy profecional, gracias porque necesito cambiar uno de esos
Salama
Those suck I bought some different company and its a mess and glue don't work, I took off and replaced whole axle, which are cheap and did myself
Abdul-Nasir
I put this kit on but with bilsteins set at 2.1 and left out the pre load spacer. Angle is steep but sitting on 35's there is no rubbing on anything. Maby try some of those.
Everard
Mi sembrava fosse da 32 il dado del mozzo e non 36
Darrius
you are a great teacher
Arth
Great video. Very simple and well explained. Thank you!
Hamilton
Put a homemade 2 inch spacer blocks between the front subframe and motor and tranny to keep lower control arms straight to keep CV shafts straight and keep axle boots from ripping.
Adok
lol i a jackstand even necessary you could probably pick the truck up with one hand. jk good work staying safe :)