Replacement trunk lock cylinder on GMC Acadia

Body Specialist

Timothy King

You want to know how to remove trunk lock cylinder in your vehicle, I’ll show you the article how to change trunk lock cylinder very easy and efficient way!

If you feel that something wrong with information above, so inform us about that!

How do you install a trunk lock on a GMC Acadia 2022?

Installing new door locks, trunk lock, and ignition tumbler. Jade part 90 The rod pretty simple it slips in and just the spring holds it in place. And then your little horseshoe clip the tab is always going to face towards the inside of the vehicle.

How do you open a broken trunk latch on a 2014 GMC Acadia?

How to Fix A Trunk That Won't Open - And that's what we're looking for that glow-in-the-dark pull handle i just gotta pull it upwards and it should pop. Open. Now that it's open i'll just have to crawl my way back out of here.

Does 2015 GMC Acadia have sliding doors?

Convenient and time-saving, the available hands-free power sliding side doors and hands-free power liftgate let you kick your foot under the door or liftgate to open with ease, so you can quickly load up and get going on your next adventure.

What cars compare to GMC Acadia 2008?

Luxury compact crossover options are plentiful. The BMW X3 ($43,700), Audi Q5 ($45,600) and Mercedes GLC ($43,850) are probably the closest GV70 competitors. The Volvo XC60 ($42,650) and Acura RDX ($40,100) would be right there as well, if you aren't as brand-snobbish.

How do you take the trunk lock off a 65 Mustang on a GMC Acadia?

To remove the '65-'66 trunk lock cylinder, turn the key clockwise as if to open the trunk, depress this pin with a small screwdriver or punch, and remove the lock cylinder.

How could a failed boot affect the engine on a GMC Acadia?

Heat damage - Engine heat can burn wire insulation and boots. A damaged boot can impede proper spark plug wire seating and performance. Wire insulation that's damaged by head can allow voltage to jump to the ground rather than jumping the gap at the bottom of the spark plug.

What is GMC Acadia 2018 tailgate step?

A GMC Acadia tailgate step is a feature that makes it easier for you to access the bed of your truck. It offers a footstep and a grab bar that allow you to climb into the back of your truck to grab items that you've stored there.

What can cause weak spark on a GMC Acadia?

If you have a weak spark, you may be dealing with a:

bad spark plug wire
bad distributor cap or rotor
faulty ignition wire or coil
ignition module or ignition driver in the powertrain control module (PCM)
bad coil-on-plug coil

How many seats does a 2010 GMC Acadia have?

The GMC Acadia seats five people. The standard Cayenne Coupe seats four people, though an additional seat is available for the back. Leather upholstery, eight-way power-adjustable front seats, and a leather-wrapped steering wheel are standard.

Can a locksmith fix a trunk latch on a GMC Acadia?

Whether the problem is with the lock cylinder or the lock assembly, replacement and maintenance require the trunk to be opened. Even with replacement parts, you may benefit from the presence of a professional locksmith to open the trunk and fix the issue.

Add comment

Comments on how to fix trunk lock cylinder on a GMC Acadia:

Brown

What size is the axle nut

Manning

I have to say a big thank you for this video. The lightbulb is expensive enough and to have it installed is ridiculous. After watching this my son and myself changed out my bulb and we used a T 20 wrench to take the covering off above the wheel. And, not all GMC Acadia’s have the HID headlight. Make sure you know which bulb to replace. Mine is an HID.

Viraj

I have a 2011 gmc acadia and there is NO cabin air filter

Stok

Great video. Just remember to move the passenger seat up first, so it's out of the way removing the battery. Also, make sure to buy a vent tube adapter before swapping battery. Mine broke off and the new battery did not include the valve. Cheers!

Edward

I HAVE BEEN TINKERING WITH CARS FOR OVER 55 YEARS - THIS IS THE STUPIDEST ARRANGEMENT FOR HEAD LIGHT BULBS THAT I HAVE EVER SEEN. ONCE YOU DO GET THE PROTECTIVE COVER OFF YOUR WHOLE HAND WILL NOT FIT INSIDE TO GRASP THE BULB - I COULD ONLY GET TWO FINGERS ON IT TO LOOSEN IT - IF THE BULB HAS BEEN IN THERE A WHILE IT TAKES QUITE A BIT OF PRESSURE TO GET IT LOOSE - THE WIRES NEED TO BE LONGER SO THAT ONCE YOU DO GET THE DAMNED THING LOOSE YOU CAN HAVE AN EASIER TIME GETTING THE OLD BULB OUT AND THE NEW ONE IN - NOW COMES THE TRICKY PART - PUTTING THE BULB ASSEMBLY BACK IN WITHOUT TOUCHING THE BULB - BY THE TIME YOU REACH THIS STAGE THE NITRILE GLOVES ARE TOAST - AFTER FIGHTING WITH SIDE 1 I DECIDED TO JUST TAKE THE DAMNED TIRE OFF AND I HAD TO ENLIST HELP HOLDING THE COWLING BACK SO THAT I COULD REACH EVERYTHING.

Brighton

is it necessary to disconnect the battery? I dont see any type of work being done with hot wires or anything that would seem to actually require that but I was just curious. Also, I thought there may be a capacitor that would still hold the charge even if you disconnected the battery? I am getting ready to do this job and I appreciate this video. I was also just wondering if you disconnect the battery what all will that reset on the denali? Clocks, oil change service tracking etc?

Lorimer

Thank you had no idea how to change it.

Amell

Great video! This video helped me a lot to replace the same sensor on my 2016 Traverse. Thanks!

Bernardo

Thankyou for the great video. I'm seeing this job in my near future. Its awesome knowing what I am getting into before starting. Extremely helpful, thanyou again

Colan

I used to hold engineers in such high esteem until I saw this...

Jae

It be nice if you could hear anything you were saying

Elene

I had the same experience yesterday, Pep boys sold me one and told me mine was bad. I bought it and there is none in there. Scam

Lud

My problem is slightly different - I have condensation inside the plastic headlight assembly. The light has always been aimed low (I bought the car used from CarMax) so I expected to find the bulb not installed correctly, especially since the condensation showed up in the past few weeks. I thought I could just open the hood and remove and re-install the bulb (like in the old days) or easily remove and re-install the whole assembly (like my GMC pickup at work). I had half the front end of the car apart and was well into my second beer before I looked at this video. Great video, thanks, but if the morons who design cars now had to work on them, they would be designed differently. I was never able to fix the condensation problem (yet) and after this mess and other stupid design flaws in this car, I'll never buy another GMC. But, thanks for the video!