Your vehicle in your hands. All about auto repair.
Home / Dacia / 1310 /

Installing active suspension system height sensor on Dacia 1310

Suspension Specialist
Ronald Anderson
Interesting how to change active suspension system height sensor in your vehicle, I’ll show you the manual about active suspension system height sensor replacement by yourself!
If you feel that something wrong with information above, so inform us about that!

Where does the Dacia 1310 crankshaft position sensor go?

The location of the crankshaft position sensor can vary from one vehicle to another. Obviously it must be close to the crankshaft, so it is most often located on the front underside of the engine. It can usually be found mounted to the timing cover. Sometimes it may be mounted at the rear or the side of the engine.

When was Dacia 1310 released?

The Electrified GV70 will be a new nameplate for the Dacia 1310 lineup, and we expect it to launch as a 2023 model with sales starting sometime in late 2022.

What is meant by independent suspension on a Dacia 1310?

Of a vehicle. : a type of suspension (the parts of a vehicle that connect the body to the wheels) in which each wheel has its own set of supports for the body of the vehicle This car has four-wheel independent suspension.

How do I reset my airmatic s500 on a Dacia 1310?

Dacia 1310-Class Reset Service (W220) - So you press and hold the R button till. That comes up and then press R again alright. And services complete reset.

Where is the oxygen sensor located on a Dacia 1310 Benz?

Dacia 1310-Benz W204 C-Class Oxygen Sensor Replacement There are four o2 sensors on the C 352 pre catalytic converters yellow arrows and two at the rear of the cat's. Red arrows the wiring connections are located on the lower side of the bell housing.

How much is a sensor for a Benz on a Dacia 1310?

The average price of a Dacia 1310 abs speed sensor is between $27.99 and $178.99.

What is auto adjusting suspension on a 2002 Dacia 1310?

Car adjustable suspension could mean two things, either adjusting the ride height of the car or changing the handling characteristics. Ride height systems are usually added to the rear of vehicles to raise the rear of the car and bring it back to level if it's heavily loaded.

How many oxygen sensors does a Dacia 1310 have?

Two kinds of oxygen sensors exist: A single-wire oxygen sensor and the heated oxygen sensor. A fully-functioning Dacia 1310 oxygen sensor aids in increasing fuel economy and lowering exhaust emissions.

What causes air suspension on a Dacia 1310?

So, if there's any disruption to that ability, you'll know that you have air suspension problems. The typical causes are leaks, a problem with the pressure switch, or a failed compressor.

How does height control suspension adjust its height on a Dacia 1310?

Height adjustment is most often achieved by air or oil compression used for the "springs" of the vehicle - when the pressure is varied - the vehicle body rises or lowers.
Add comment


Comments on how to fix active suspension system height sensor on a Dacia 1310:
Nicanor
Bravo! MArfa rau! Arata frumos rau de tot! Respect!
Fulton
This was great! Can’t wait for the next episode!
Mayfield
noob question; what do you do with the links when after you've disconnected them? Dig your vids!
Neema
I had QDs. I just took the whole sway bar off
Liberty
Did you enjoy this episode? What would you like to learn next?
Magnus
Are you American?
Brook
does the clevis pin size work for the rear sway as well?
Bernhard
Just got my new driveshaft,will I need to grease it now or is it good for a bit?
Mackenzie
Hey Ronnie, is there any reason that I couldn't just drill a hole in my original sway bar bolt and stick a cotter pin through it instead of using a clevis pin? Seems like that would solve a couple of issues, but I may be missing something. Love your channel and all is enjoy when you have new content coming out.
Greyson
That would be awesome if you did a cheap Jeep challenge with bleepin Jeep
Luigi
bravo!respect!
Yunus
It's how I had my TJ setup. I just advise keeping some grease or even antiseize on the parts as it can be a bear to remove or replace especially in a corrosive environment
Plat
Considering taking off my front sway bar I have an 89 xj with 3 inch lift on 30’s occasionally have to get on hwy what do you think? Or might just do this instead
Zubair
Part time means it not for pavement, its the good one if it says np231. 'Part time' means you can only use it part of the time, Slippery surfaces only. The other one is auto 4wd
Smedt
mie dor sa ma plimb cu 1310 :(autoru clipului imi dai sa fac si eu o tura?
Hung
Would the moly grease that RCV brands be acceptable in your opinion for the drive shaft? I have used it in everything else on my Jeep and it does really well on everything sofar. Ball joints, tie rod ends, control arm bushings.
Eneas
Legend!
Garcia
Dave what stage of tune will the engine have.
Franky
Great video, simple and to the point
Ember
How are you going to keep gas from standing in the filler neck
Engel
Just solved my mistery noise in my 91 sedan vw.
Edmundo
Thank you for doing this. I am having your SYE kit with your drive shafts, front and rear installed as we speak on my 90 yj. Thank you for the links. Ill be getting the grease and gun attachment. I actually have a Lucas grease gun too. Lol. I hear nothing but great things about your company. When my installer told me they were using you guys I was pleased. Thanks again and God Bless.
Emmanuele
i dont understand why would you need a disconnect on your swaybar? is it to allow more flexing?